Hauppauge 哈帕克 WinTV HVR 930C (DVB-C, DVB-T, 类似物, USB 2.0)

多媒体 DVB-C, DVB-T, 哈帕克 (Hauppauge), 电视, USB

Hauppauge 哈帕克 WinTV HVR 930C (DVB-C, DVB-T, 类似物, USB 2.0)
4 投票, 平均: 3.5 出最多 54 投票, 平均: 3.5 出最多 54 投票, 平均: 3.5 出最多 54 投票, 平均: 3.5 出最多 54 投票, 平均: 3.5 出最多 5
  ( 3.5 4 等级)

Hauppauge 哈帕克 WinTV HVR 930C 
Minimum: ¥ 0.00 
Maximum: ¥ 0.00  
更新: 16/08/2015 09:57


The Hauppauge WinTV HVR 930C can easily be mixed up with the Hauppauge WinTV HVR 930C HD, which can only be distinguished by the additional term “HD”. The HD version is not supported by Linux, while the non-HD version is. The non-HD version has the USB ID 2040:1605, while the HD version has the USB ID 2040:b130.

The USB stick uses the kernel modules xc5000, drxk and em28xx. These modules are part of the Linux kernel since version 3.3. The kernel recognized the USB stick in the following way:

usb 2-1.2.5: new high speed USB device number 9 using ehci_hcd
usb 2-1.2.5: New USB device found, idVendor=2040, idProduct=1605
usb 2-1.2.5: New USB device strings: Mfr=0, Product=1, SerialNumber=2
usb 2-1.2.5: Product: WinTV HVR-930C
usb 2-1.2.5: SerialNumber: 4034722785
em28xx: New device WinTV HVR-930C @ 480 Mbps (2040:1605, interface 0, class 0)
em28xx: Audio Vendor Class interface 0 found
em28xx: Video interface 0 found
em28xx: DVB interface 0 found
em28xx #0: chip ID is em2884
em28xx #0: Identified as Hauppauge WinTV HVR 930C (card=81)
Registered IR keymap rc-hauppauge
input: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2.5/rc/rc2/input14
rc2: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2.5/rc/rc2
em28xx #0: Config register raw data: 0x2a
em28xx #0: I2S Audio (3 sample rates)
em28xx #0: No AC97 audio processor
em28xx #0: v4l2 driver version 0.1.3
em28xx #0: V4L2 video device registered as video0
em28xx-audio.c: probing for em28xx Audio Vendor Class
em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab
drxk: status = 0x439130d9
drxk: detected a drx-3913k, spin A2, xtal 20.250 MHz
DRXK driver version 0.9.4300
drxk: frontend initialized.
xc5000 1-0061: creating new instance
xc5000: Successfully identified at address 0x61
xc5000: Firmware has not been loaded previously
DVB: registering new adapter (em28xx #0)
DVB: registering adapter 1 frontend 0 (DRXK DVB-C DVB-T)...
em28xx #0: Successfully loaded em28xx-dvb

The kernel modules need the original firmware copied to /lib/firmware To access the tuners.
If the firmware was not already installed by the distribution (e.g. in Ubuntu with the program “Additional driver”), the following files have to be copied:

wget http://www.wintvcd.co.uk/drivers/HVR-9x0_5_10_325_28153_SIGNED.zip
unzip HVR-9x0_5_10_325_28153_SIGNED.zip
dd if=HVR-900/emOEM.sys of=dvb-usb-hauppauge-hvr930c-drxk.fw bs=1 skip=71600 count=42692
sudo cp dvb-usb-hauppauge-hvr930c-drxk.fw /lib/firmware/

After successful initialization of the modules the following devices are created


to access the stick.

If it should be necessary to compile the kernel modules by hand (e.g. if a linux version older than 3.3 is used), the following packages are needed:

sudo apt-get install libproc-processtable-perl build-essential linux-headers-$(uname -r)

The module source has to be downloaded (i.e. copied from its GIT repository). Code compilation is performed in the folowing way:

sudo rm -r media_build
git clone git://linuxtv.org/media_build.git
cd media_build
sudo make install; sudo make load

确定硬件配置 (1 结果)

这种硬件组件在以下系统配置下使用的Linux用户。这些结果通过收集我们的 扫描工具:
Linux Mint 18 Sarah 4.4.0-45-generic - 04/11/2016


scroll left scroll right


请使用注释部分提出更正的文章,以及相关的摘录 lspci -nnv, lsusb -v, lshw, dmesg ... 此外,使用一节的经验与此硬件组件或搜索该硬件的其他业主配置帮助交流。
Submitting comment...