Rollei DF-S 100 SE (Film Scanner, Slide Scanner, USB)

Misc Filmscanner, Rollei, Scanner, Diascanner, USB

Rollei DF-S 100 SE (Film Scanner, Slide Scanner, USB)
Linux compatibiliteit:
2 Beoordelingen, gemiddelde: 4,0 van de maximale 52 Beoordelingen, gemiddelde: 4,0 van de maximale 52 Beoordelingen, gemiddelde: 4,0 van de maximale 52 Beoordelingen, gemiddelde: 4,0 van de maximale 52 Beoordelingen, gemiddelde: 4,0 van de maximale 5
  ( 4 big 2 beoordelingen)

Prijs: EUR 54,00 (op voorraad)
(+ Verzendkosten: EUR 6,99)

 Verkrijgbaar bij Redcoon.nl



Linux compatibiliteit

The Rollei DF-S 100 SE is a film and slide scanner, which can be connected via USB with the PC. The scanner is equipped with a small internal display, which allows to preview the positioning of the slides or film negative while scanning. The DF-S 100 SE is fully controlled by the buttons on the device and the menu that is shown on the internal display. Furthermore, the scanner has a SD card slot. The inserted SD card is used for storing the scanned images.

The scanner can also be used under Linux, since it can be controlled independently from any PC. It is not possible to see the current image (the one which is shown on the integrated screen) on the PC. But access to the scanned images which are stored on the SD card is possible under Linux, either by using a SD card reader or via USB (see below). The device is very picky, which kind of SD card is used, e.g. if micro SD cards (with adapter) are inserted, the device still starts, but the menu is scrambled and scanning of images takes 10 times as long as normal without storing the images on the SD card. It is therefore recommended to use an “old style” SD card for this device (i.e. low speed class and not micro SD card with adapter). Furthermore, it is a good idea to format the SD card inside the DF-S 100 SE by using the corresponding menu options. This ensures that the file system of the SD card is compatible.

Connecting the DF-S 100 SE

If the DF-S 100 SE is connected via USB without an inserted SD card, it is not recognized if powered on:

usb 1-6: new high-speed USB device number 6 using ehci-pci
usb 1-6: device not accepting address 6, error -71

Instead, is is necessary to have an SD card inserted while starting the USB connected device, which has the USB ID 05e1:0b02:

usb 1-6: new high-speed USB device number 4 using ehci-pci
usb 1-6: New USB device found, idVendor=05e1, idProduct=0b02
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: Product: DF-S100SE
usb 1-6: Manufacturer: Rollei
usb 1-6: SerialNumber: 0123456789AC
usb-storage 1-6:1.0: USB Mass Storage device detected
scsi8 : usb-storage 1-6:1.0
mtp-probe: checking bus 1, device 4: "/sys/devices/pci0000:00/0000:00:12.2/usb1/1-6"
mtp-probe: bus: 1, device: 4 was not an MTP device
usb 1-6: USB disconnect, device number 4

The DF-S 100 SE can now be used for scanning film negatives or slides. The corresponding images are stored on the interal SD card. To access these images without removing the SD card each time, the USB connection symbol has to be selected. The DF-S 100 SE then allows to access the SD card memory via USB. Under Ubuntu 14.10 the SD card is then automatically mounted and can be accessed to copy the images for further processing:

usb 1-6: reset high-speed USB device number 11 using ehci-pci
scsi 11:0:0:0: Direct-Access     Syntek   USB MSDC         1.00 PQ: 0 ANSI: 1
sd 11:0:0:0: Attached scsi generic sg3 type 0
sd 11:0:0:0: [sdc] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
sd 11:0:0:0: [sdc] Write Protect is off
sd 11:0:0:0: [sdc] Mode Sense: 02 00 00 00
sd 11:0:0:0: [sdc] No Caching mode page found
sd 11:0:0:0: [sdc] Assuming drive cache: write through
sd 11:0:0:0: [sdc] No Caching mode page found
sd 11:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 11:0:0:0: [sdc] No Caching mode page found
sd 11:0:0:0: [sdc] Assuming drive cache: write through
sd 11:0:0:0: [sdc] Attached SCSI removable disk
FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Mounted /dev/sdc1 at /media/xyz/CANON_DC on behalf of uid 1000

From then on, the DF-S 100 SE is visible via the lsusb command:

Bus 001 Device 011: ID 05e1:0b02 Syntek Semiconductor Co., Ltd

If the device is not in USB mode, it is not shown by USB. The USB connection is only used for power supply of the DF-S 100 SE.


Vergelijkbare Linux hardware

scroll left scroll right

Reageren en beoordelen

Laat in de comments sectie beoordeling of commentaar en correcties op het artikel. Bijzonder nuttig zijn Ausz navigatie gebruik van ge lspci -nnk, lsusb, lshw, dmesg, enz, indien deze niet worden opgenomen in het artikel. Blijft het serveren. Het commentaar gebied van ervaringen tussen de eigenaars van de hardware-component en de Zoeken Configuratie Help Hotel
 
E-mailadres wordt niet gepubliceerd.
Submitting comment...