Hama MCE Te©ecomando

I/O Infrarosso, Multimedia, Telecomando, USB

Compatibilità con Linux:
5 valutazioni, media: 5,0 su 55 valutazioni, media: 5,0 su 55 valutazioni, media: 5,0 su 55 valutazioni, media: 5,0 su 55 valutazioni, media: 5,0 su 5
  ( 5 con 5 valuationi)

Prezzo: EUR 21,90 (disponible)
(senza spese di spedizione)

 Acquistare da Amazon.it

Andamento dei prezzi
Hama MCE Te©ecomando
Minimum: EUR 15,48 
Maximum: EUR 35,68  
Aggiornato: 22/03/2016 18:37

Recensione di Compatibilità con Linux

The low priced infraread remote control and USB receiver from Hama are supported by Linux. The infraread signals are transferred to the system per /dev/input/event device and are interpreted from the Linux kernel as keyboard and mouse events. Hence, even the mouse pointer can be controlled by the gray round controller, which is availabe at the remote.

Sending and receiving does not support transmitting of repeated signals, which occurs if a button stays pressed. Instead, the button has to be pushed repeatedly (this could eventually limit the application scenario of the remote).

After plugging the receiver into the USB port it is recognized by the Linux kernel (Linux version 3.2.0-24-generic) in the following way:

 [ 7553.940063] usb 3-4: new low-speed USB device number 5 using ohci_hcd
mtp-probe: checking bus 3, device 5: "/sys/devices/pci0000:00/0000:00:04.0/usb3/3-4"
[ 7554.168754] input: HID 05a4:9881 as /devices/pci0000:00/0000:00:04.0/usb3/3-4/3-4:1.0/input/input12
[ 7554.169167] generic-usb 0003:05A4:9881.0005: input,hidraw0: USB HID v1.10 Keyboard
         [HID 05a4:9881] on  usb-0000:00:04.0-4/input0
 mtp-probe: bus: 3, device: 5 was not an MTP device
[ 7554.201794] input: HID 05a4:9881 as /devices/pci0000:00/0000:00:04.0/usb3/3-4/3-4:1.1/input/input13
[ 7554.202327] generic-usb 0003:05A4:9881.0006: input,hidraw1: USB HID v1.10
          Mouse [HID 05a4:9881] on usb-0000:00:04.0-4/input1
[ 7554.636766] input: HID 05a4:9881 (lircd bypass) as /devices/virtual/input/input14

and the necessary input devices, which transfer the keyboard and mouse events to the system, are created automatically. The USB ID shown by lsusb is the following:

Bus 003 Device 003: ID 05a4:9881 Ortek Technology, Inc.

Usually the events of the remote are interpreted by the kernel like a keyboard of mouse event without the need of an additional driver. But if it is required to use the remote together with LIRC the LIRC driver devinput has to be activated:

# /etc/lirc/hardware.conf
#Chosen Remote Control
REMOTE="Hauppauge TV card"
REMOTE_MODULES="lirc_dev lirc_i2c"

It can happen that the numbering of the input devices (event1, event2, …) is reshuffled at each reboot of the PC because the hardware gets recognized in different orders at each boot. In this case on should use the unvariable device files “/dev/input/by-id/usb-...” instead of “/dev/input/eventX“.

A detailed configuration of the remote together with LIRC can be found at VRC-1100 Ortek Technology MCE Clone Remote.

Configurazioni hardware identificati (2 Risultati)

Questo componente hardware è stato utilizzato dagli utenti Linux nelle seguenti configurazioni di sistema. Questi risultati sono stati raccolti dal nostro LHG Scan Tool:
Versione kernel
Data di scansione
Linux Mint 18 Sarah 4.4.0-47-generic - 26/11/2016
Ubuntu 12.04.1 LTS 3.2.0-30-generic - 06/12/2014

Linux Hardware simile

scroll left scroll right


Si prega di utilizzare la sezione commenti a presentare correzioni per l'articolo e le pertinenti stralci di lspci -vnn, lsusb, lshw, dmesg, Inoltre, utilizzare la sezione per lo scambio di esperienze con questo componente hardware o ricerca di aiuto configurazione da altri proprietari di questo hardware.
L'indirizzo di posta elettronica non sarà pubblicato.
Submitting comment...