Asus USB-N13 (WiFi USB Adapteur, 802.11n, 300 Mbits, Wps)

Réseau Asus, USB, WiFi

Asus USB-N13 (WiFi USB Adapteur, 802.11n, 300 Mbits, Wps)
Examen de compatibilité avec Linux:
2 évaluations, en myoenne: 3,0 de 52 évaluations, en myoenne: 3,0 de 52 évaluations, en myoenne: 3,0 de 52 évaluations, en myoenne: 3,0 de 52 évaluations, en myoenne: 3,0 de 5
  ( 3 avec 2 évaluations)

Prix: EUR 19,24 (En stock)
(sans frais de ports)

 Achetez sur Amazon.fr



courbe de prix
Asus USB-N13 
-
Minimum: EUR 14,11 
Maximum: EUR 61,12  
Mis à jour: 03/05/2016 23:26

Examen de compatibilité avec Linux

The Asus USB-N13 exists in 2 versions, A1 and B1. Both versions can be used under Linux, however, it might be necessary to compile the driver by hand.

Version A1 (USB-ID 0b05:1784)

The version A1 has the USB ID

Bus 002 Device 003: ID 0b05:1784 ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter [Ralink RT3072]
Bus 001 Device 002: ID 0b05:1784 ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter (rev. A1) [Ralink RT3072]

and bases on the Ralink RT3072 chipset which is supported automatically by the rt2800usb kernel module
(e.g. since Linux Redhat 9.0 kernel 2.4.20, Ubuntu 9.04 kernel 2.6.28-11, Fedora10 kernel 2.6.27.5-117):

usb 1-5: new high-speed USB device number 2 using ehci-pci
usb 1-5: New USB device found, idVendor=0b05, idProduct=1784
usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-5: Product: 802.11 n WLAN
usb 1-5: Manufacturer: Ralink
usb 1-5: SerialNumber: 1.0
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usb 1-5: reset high-speed USB device number 2 using ehci-pci
ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c detected
ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
usbcore: registered new interface driver rt2800usb
ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
wlan0: authenticate with 11:22:33:44:55:66
wlan0: send auth to 11:22:33:44:55:66 (try 1/3)
wlan0: authenticated
wlan0: associate with 11:22:33:44:55:66 (try 1/3)
wlan0: RX AssocResp from 11:22:33:44:55:66 (capab=0x401 status=0 aid=2)
wlan0: associated

Alternatively, one can use the original driver from Ralink. This driver can be downloaded from the Ralink homepage (driver für RT8070 /RT3070 /RT3370 /RT5370 /RT5372 USB has to be downloaded).

After unpacking the driver

cd Downloads/
tar -jxvf 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2 .5.0.3_DPO.bz2

one has to unload the kernel module rt2800usb which is automatically loaded by the standard kernel

sudo modprobe -r rt2800usb

and inhibit the reloading of this module by blacklisting it in the file /etc/modprobe.d/blacklist.conf. The following entry has to be added:

blacklist rt2800usb
blacklist rt2800lib
blacklist rt2x00usb
blacklist rt2x00lib

The downloaded driver has to modified to work with the USB-N13 stick. In the file

~/Download/2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2 .5.0.3_DPO/os/linux/

the following two values have to be switched from « n » to « y »:

# Support Wpa_Supplicant
HAS_WPA_SUPPLICANT=y

# Support Native WpaSupplicant for Network Maganger
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y

Afterwards, the driver can be compiled:

make
sudo make install

After a reboot the compiled driver,i.e., rt5370sta.o, will load automatically which can be seen by the command:

rt5370sta 765432 1

Version B1 (USB ID 0b05:17ab)

Bus 001 Device 004: ID 0b05:17ab ASUSTek Computer, Inc. USB-N13 802.11n Network Adapter (rev. B1) [Realtek RTL8192CU]

This version bases on the RTL8192CU chipset.

The corresponding driver can be downloaded from the Ralink homepage. One finds the Linux version of the driver in the section « RTL8192CU ».

To compile this driver the following packages have to be installed as prerequisite:

sudo apt-get install linux-headers-`uname -r`
sudo apt-get install build-essential

Afterwards, the downloaded driver can be compiled by:

cd ~/Downloads/RTL8188C_8192C_USB_linux_v3.4.3_4369.20120622
sudo bash install.sh

The final output

install -p -m 644 8192cu.ko  /lib/modules/3.x.x-xx-generic/kernel/drivers/net/wireless/
  /sbin/depmod -a 3.x.x-xx-generic
##################################################
The Setup Script is completed !
##################################################

shows the successful compilation. After a reboot the compiled kernel module, i.e., 8192cu.ko, loads automatically.


Configurations matérielles identifiées (2 résultats)

Ce composant matériel a été utilisé par les utilisateurs de Linux dans les configurations système suivantes. Ces résultats ont été collectées par notre LHG Scan Tool:
Distribution
Kernel
Évaluation
Date du balayage
blackPanther OS v16.2SE (Silent Killer) 4.9.20-desktop-pae-1bP - 09/10/2017
Ubuntu 16.10 4.8.0-48-generic - 17/04/2017

Matériel Linux Similaire

scroll left scroll right

Commentaires

Utilisez la section commentaires pour nous suggérer des corrections de l'article et des sorties de commandes lspci -vnn, lsusb, lshw, dmesg, etc...
De plus, vous pouvez utiliser les commentaires pour nous communiquer vos expériences avec le matériel ou pour rechercher de l'aide pour la configuration.
 
L'adresse email n'est pas rendue publique.
Submitting comment...