> Multimedia (301)
> Multimedia > Cámara de Videovigilancia (14)
> Multimedia > Otro (10)
> Multimedia > Radio (2)
> Multimedia > Son (79)
> Multimedia > Televisión (123)
> Multimedia > Cámara Web (80)
Revisión de Compatibilidad con Linux
The Hauppauge DVB-T card is equipped with two Microtune MT2060 tuners and therefore allows parallel receiving of two different DVB-T bouquets with one attached antenna. The model number 99xxx of the PCI card is supported since Linux kernel 2.6.19 and uses the kernel module dvb_usb_dib0700.
The card is automatically initialized during booting by the kernel (Ubuntu 10.4, Kernel 2.6.38) in the following way:
[ 18.482739] dib0700: loaded with support for 15 different device-types [ 18.482894] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 18.483681] lirc_dev: IR Remote Control driver registered, major 250 [ 18.485284] IR LIRC bridge handler initialized ... [ 18.482739] dib0700: loaded with support for 15 different device-types [ 18.482894] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 18.483681] lirc_dev: IR Remote Control driver registered, major 250 [ 18.485284] IR LIRC bridge handler initialized [ 19.988068] MT2060: successfully identified (IF1 = 1207) [ 20.568015] Registered IR keymap rc-dib0700-rc5 [ 20.570122] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1e.0/0000:04:02.2/usb2/2-1/rc/rc0/input2 [ 20.570368] rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1e.0/0000:04:02.2/usb2/2-1/rc/rc0 [ 20.570520] dvb-usb: schedule remote query interval to 50 msecs. [ 20.570525] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected. [ 20.571509] usbcore: registered new interface driver dvb_usb_dib0700
The card has the USB ID 2040:9950
Bus 002 Device 002: ID 2040:9950 Hauppauge
The access the card the following kernel modules are used:
rc_dib0700_rc5 12460 0 dvb_usb_dib0700 62306 2 dib7000p 27746 1 dvb_usb_dib0700 dib0090 23186 1 dvb_usb_dib0700 dib7000m 22939 1 dvb_usb_dib0700 dib0070 18078 1 dvb_usb_dib0700 dvb_usb 23658 1 dvb_usb_dib0700 dib8000 37054 1 dvb_usb_dib0700 dvb_core 90587 3 dib7000p,dvb_usb,dib8000 dib3000mc 22898 3 dvb_usb_dib0700 dibx000_common 13533 4 dib7000p,dib7000m,dib8000,dib3000mc rc_core 25760 10 rc_dib0700_rc5,ir_lirc_codec,dvb_usb_dib0700,ir_sony_decoder, ir_jvc_decoder,ir_rc6_decoder,dvb_usb,ir_rc5_decoder,ir_nec_decoder
Warning: Hauppuage uses the same naming and packaging for different versions of this card. Only one of these versions is equipped with one coaxial connector. The other model equipped with two coaxial connectors might not be supported by Linux. To be sure that the card is supported it should be made sure that the one-coaxial-connector version is used.
The DVB-T card is also equipped with a Low Noise Amplifier (LNA) for both tuners in case of bad Signal-to-Noise ratio. The LNA has to be activated by hand. This is done while the loading of the module by adding the following option:
options dvb_usb_dib0700 force_lna_activation=1
These additional options are added to the file /etc/modprobe.d/options.conf in Ubuntu. Other distributions might store these options in a different file, e.g. /etc/modprobe.d/options.