Hama MCE Mando a Distancia

I/O Infrarrojo, Multimedia, Mando a distancia, USB

Hama MCE Mando a Distancia
Compatibilidad con Linux:
5 votos, media: 5,0 sobre un total de 55 votos, media: 5,0 sobre un total de 55 votos, media: 5,0 sobre un total de 55 votos, media: 5,0 sobre un total de 55 votos, media: 5,0 sobre un total de 5
  ( 5 con 5 valoraciones)

Precio: EUR 15,42 (disponible)
(sin gastos de envío)

 comprar a Amazon.es



Tendencia del precio
Hama MCE Mando a Distancia
-
Minimum: EUR 6,95 
Maximum: EUR 36,23  
Actualizado: 21/06/2016 03:40

Revisión de Compatibilidad con Linux

The low priced infraread remote control and USB receiver from Hama are supported by Linux. The infraread signals are transferred to the system per /dev/input/event device and are interpreted from the Linux kernel as keyboard and mouse events. Hence, even the mouse pointer can be controlled by the gray round controller, which is availabe at the remote.

Sending and receiving does not support transmitting of repeated signals, which occurs if a button stays pressed. Instead, the button has to be pushed repeatedly (this could eventually limit the application scenario of the remote).

After plugging the receiver into the USB port it is recognized by the Linux kernel (Linux version 3.2.0-24-generic) in the following way:

 [ 7553.940063] usb 3-4: new low-speed USB device number 5 using ohci_hcd
mtp-probe: checking bus 3, device 5: "/sys/devices/pci0000:00/0000:00:04.0/usb3/3-4"
[ 7554.168754] input: HID 05a4:9881 as /devices/pci0000:00/0000:00:04.0/usb3/3-4/3-4:1.0/input/input12
[ 7554.169167] generic-usb 0003:05A4:9881.0005: input,hidraw0: USB HID v1.10 Keyboard
         [HID 05a4:9881] on  usb-0000:00:04.0-4/input0
 mtp-probe: bus: 3, device: 5 was not an MTP device
[ 7554.201794] input: HID 05a4:9881 as /devices/pci0000:00/0000:00:04.0/usb3/3-4/3-4:1.1/input/input13
[ 7554.202327] generic-usb 0003:05A4:9881.0006: input,hidraw1: USB HID v1.10
          Mouse [HID 05a4:9881] on usb-0000:00:04.0-4/input1
[ 7554.636766] input: HID 05a4:9881 (lircd bypass) as /devices/virtual/input/input14

and the necessary input devices, which transfer the keyboard and mouse events to the system, are created automatically. The USB ID shown by lsusb is the following:

Bus 003 Device 003: ID 05a4:9881 Ortek Technology, Inc.

Usually the events of the remote are interpreted by the kernel like a keyboard of mouse event without the need of an additional driver. But if it is required to use the remote together with LIRC the LIRC driver devinput has to be activated:

# /etc/lirc/hardware.conf
#
#Chosen Remote Control
REMOTE="Hauppauge TV card"
REMOTE_MODULES="lirc_dev lirc_i2c"
REMOTE_DRIVER="devinput"
REMOTE_DEVICE="/dev/input/event2"
REMOTE_SOCKET=""
REMOTE_LIRCD_CONF="/etc/lirc/hama.txt"
REMOTE_LIRCD_ARGS=""

It can happen that the numbering of the input devices (event1, event2, …) is reshuffled at each reboot of the PC because the hardware gets recognized in different orders at each boot. In this case on should use the unvariable device files “/dev/input/by-id/usb-...” instead of “/dev/input/eventX“.

A detailed configuration of the remote together with LIRC can be found at VRC-1100 Ortek Technology MCE Clone Remote.


Configuraciones de hardware identificados (2 Resultados)

Este componente de hardware fue utilizado por los usuarios de Linux en las siguientes configuraciones del sistema. Estos resultados se recogieron por nuestra LHG Scan Tool:
Distribución
Versión del núcleo
Valoración
Fecha de exploración
Linux Mint 18 Sarah 4.4.0-47-generic - 26/11/2016
Ubuntu 12.04.1 LTS 3.2.0-30-generic - 06/12/2014

Hardware de Linux similares

scroll left scroll right

Commentarios

Por favor, emplee la sección de comentarios para indicar correciones del artículo así como extractos de lspci, lsusb, lshw, dmesg etc. Además, utilice la sección para el intercambio de experiencias con este componente de hardware o para obtener ayuda para la configuración de otros propietarios de este mismo hardware.
 
La dirección de correo electrónico no será publicada
Submitting comment...